Wipers - Type 033

The Hallite 33 wiper has a lip designed to remove lightly adhered dirt from the rod i.e. mud, dust or moisture. The wiper is manufactured from a hard nitrile rubber suitable for installing in a grooved housing. Rod diameters (d1) of 20mm and below require a two piece housing. To prevent dirt passing the outside of the wiper and to reduce the pumping action, the outside diamter is an interference fit with the housing. Certain sizes of the standard Hallite 33 metric range are suitable for ISO6195 Housing Type A. Wipers are installed in the sealing configurations of hydraulic cylinders to prevent contaminants such as dirt, dust and moisture from entering the cylinder as they retract back into the system. Contamination can cause significant damage to the rod, cylinder wall, seals, and other components, and is one of the primary causes of premature seal and component failure in a fluid power system. HES and Hallite offer a wide range of hydraulic wipers in High Performance Hallite® 361 polyurethane, Nitrile®, Hythane® 181 and other polyester based materials, along with press-fit metal caged ranges. The wiper seal is the most undervalued seal type in the hydraulic cylinder in relation to its important function. Particular attention should be drawn to its selection, the surrounding environment and service conditions must also be taken into special consideration. Hydraulic Equipment Supermarkets are your approved Hallite supplier. If the type 33 wiper you need is not listed contact HES on 01452 730774 or email enquiries@hydraulicequipment.net

Ordering	Description	Price	Quantity
50mm ID 62mm OD 6mm Hsg Type 033	Wiper with free UK delivery	Call for pricing + VAT	Qty:
25mm ID 33mm OD 4mm Hsg Type 033	Wiper with free UK delivery	Call for pricing + VAT	Qty:
45mm ID 57mm OD 6mm Hsg Type 033	Wiper with free UK delivery	Call for pricing + VAT	Qty:
14mm ID 22mm OD 4mm Hsg Type 033	Wiper with free UK delivery	Call for pricing + VAT	Qty:
40mm ID 48mm OD 5mm Hsg Type 033	Wiper with free UK delivery	Call for pricing + VAT	Qty:

Technical information
Delivery & Returns
Downloads & Catalogues

See Download Tab for data sheet

For more information contact HES on 01452 730774 or email enquiries@hydraulicequipment.net

Delivery Information and Returns Policy

Delivery Information :

Delivery charges apply.

If you require International Delivery charges will apply and you will need to contact enquiries@grouphes.com to process your order.

Delivery will be Next Working Day wherever possible if the order is made before 4pm or 2pm for any order of oil. Please allow up to 7 working days for any orders of 205 litre/45 gallons barrels of oil or 1000L IBCs.

Returns policy:

You are entitled to cancel your order and return the product to any division of Group HES within 7 working days from delivery date. After this date, it will be at the discretion of management to decide whether a refund or exchange will be given. A full refund is available if the item is unused, undamaged and in the original packaging. The item must not contain any fluids, including water, oil etc.

An average 20% (percentage may vary), handling charge will be applicable unless the part is faulty or incorrectly described. Any shipping costs will not be refunded.

If you need to return an item, please contact admin@grouphes.com immediately with your order number and reason for return.

Please allow up to 30 days for refunds to be applied or alternatives to be resent out. The company reserves the right to assess whether there is any consumer error involved and will take this into account when refunds are granted.

Your statutory rights are not affected.

These terms are subject to change so do check back regularly.

If you need to return an item due to warranty reasons - please refer to our Terms and Conditions and contact admin@grouphes.com or call 01452 730 774.

Product Files